Pitt Town Bottoms vs Wilberforce

Name: Water Quality Comparison: Pitt Town Bottoms vs Wilberforce
Creator: WaterScore
License: https://creativecommons.org/licenses/by/4.0/

Side-by-side tap water quality comparison

Pitt Town Bottoms, NSW

9.5

Quality Score

Supplied by Sydney Water

Wilberforce, NSW

9.6

Quality Score

Supplied by Sydney Water

Share this page Twitter Facebook LinkedIn

Which suburb has better water?

It's very close! Pitt Town Bottoms scores 9.5/10 and Wilberforce scores 9.6/10. Both suburbs have similar water quality based on ADWG compliance data.

As an Amazon Associate, WaterScore earns from qualifying purchases. We may also earn from other affiliate links on this page — this doesn't affect our recommendations.

Recommended for this suburb

Fluoride in Wilberforce is 1.03 mg/L — above the 1.0 mg/L threshold. If you want it out, a carbon pitcher won't do it.

This is the fluoride mistake almost every family makes: they buy a Brita or a basic tap filter, assume it's handling fluoride, and it isn't. Activated carbon doesn't touch fluoride ions. Neither does boiling — that actually concentrates it. Reverse osmosis (85–95% removal) and activated alumina are the only two consumer technologies that measurably reduce fluoride at the tap.

iSpringOur pick

RCC7AK 6-Stage Under-Sink RO (with Alkaline Re-min)

4.6 · 13,756 ratings on Amazon

A 6-stage RO system drops fluoride from 1.03 mg/L down to near-zero, and handles chlorine, lead and dissolved solids at the same time. Under-sink mount, its own tap on the bench.

Remove fluoride →

Sponsored Amazon link · we may earn a commission at no cost to you. Check Amazon for current price and availability.

Visual comparison

Pitt Town Bottoms, NSW

Wilberforce, NSW

Key metrics comparison

Hardness (mg/L)

Pitt Town Bottoms

49.9 Higher

Wilberforce

39.1 Lower

pH Level

Pitt Town Bottoms

7.9 Normal

Wilberforce

7.8 Normal

Fluoride (mg/L)

Pitt Town Bottoms

1.01 Lower

Wilberforce

1.03 Higher

Chlorine (mg/L)

Pitt Town Bottoms

0.04 Lower

Wilberforce

1.13 Higher

Full water quality comparison

All parameters compared against Australian Drinking Water Guidelines (ADWG)

Parameter	Pitt Town Bottoms	Wilberforce	Unit	ADWG Guideline
Aluminium	0.013 Good	0.01 Good	mg/L	< 0.2
Ammonia	0.226 Measured	0.001 Measured	mg/L	No limit
Chloride	0.004 Good	0.004 Good	mg/L	< 250
Colour	3 Good	2 Good	HU	< 15
Copper	0.019 Good	0.014 Good	mg/L	< 2
Dissolved Oxygen	102.7 Measured	85.1 Measured	% saturation	No limit
E. coli	0 Compliant	0 Compliant	orgs/100 mL	< 0
Fluoride	1.01 Good	1.03 Good	mg/L	< 1.5
Free Chlorine	0.04 Good	1.13 Good	mg/L	< 5
Hardness	49.9 Good	39.1 Good	mg/L	< 200
Iron	0.006 Good	0.018 Good	mg/L	< 0.3
Manganese	0.0017 Good	0.0005 Good	mg/L	< 0.1
Monochloramine	1.74 Good	0.07 Good	mg/L	< 3
Ndma	0.0001 Measured	0.0001 Measured	mg/L	No limit
PFOA	0.0002 Good	0.0009 Good	µg/L	< 0.2
PFOS + PFHxS	0.0014 Good	0.0028 Good	µg/L	PFOS < 0.008, PFHxS < 0.03
pH	7.9 Normal	7.8 Normal	pH units	6.5 – 8.5
Sulfate	8.8 Good	10.4 Good	mg/L	< 500
Temperature	19 Measured	20.9 Measured	degrees C	No limit
Total Dissolved Solids	137 Good	145 Good	mg/L	< 600
Trihalomethanes	0.09 Good	0.04 Good	mg/L	< 0.25
Turbidity	0.11 Good	0.15 Good	NTU	< 5
Zinc	0.002 Measured	0.004 Measured	mg/L	No limit

Explore further

Pitt Town Bottoms

Wilberforce

Disclaimer: This comparison is for general informational purposes only and does not constitute medical advice or professional guidance. Data is sourced from Sydney Water. Values shown are based on the most recent published water quality reports and may not reflect real-time conditions at your tap. Water quality can vary due to local plumbing, seasonal changes, and other factors. For specific health concerns, consult a qualified health professional or contact your local water utility. See our Terms of Use.