Tap Water Quality in Mount Havelock, SA
Postcode 5434 · Supplied by SA Water via Hawker
Quality Score
About Mount Havelock
Mount Havelock is a suburb in South Australia, Australia (postcode 5434). It falls within the SA Water area. Neighbouring suburbs include Prelinna, Shaggy Ridge, Black Hill Station, Barndioota.
Tap water in Mount Havelock is supplied by SA Water. The suburb receives water via the Hawker supply zone.
Water quality summary
Based on 2025 water quality reports, Mount Havelock achieves a WaterScore of 9.0 out of 10, rated excellent overall. Water hardness measures 89 mg/L, classified as moderately hard. This may cause light mineral deposits on fixtures over time. The pH level is 0.05, which is outside the ADWG guideline range of 6.5–8.5. Fluoride levels are very low at 0.1 mg/L, indicating the water is not significantly fluoridated. Chlorine, used for disinfection, measures 1.1 mg/L — well within the ADWG guideline of 5 mg/L. Some residents may notice a slight taste, which can be reduced by refrigerating water or using a carbon filter. Total dissolved solids (TDS) measure 298 mg/L, considered low against the ADWG guideline of 600 mg/L. Turbidity is 0.1 NTU, indicating clear water, within the ADWG guideline of 5 NTU. E. coli was not detected in testing, meeting the ADWG standard for microbiological safety.
Compare with nearby suburbs: Prelinna , Shaggy Ridge , Black Hill Station
Recommended filters for Mount Havelock
Products matched to your water profile
BRITA
Marella 2.4L Fridge Water Filter Jug (Maxtra+)
4.7 · 16,095 ratings on Amazon
Ideal for Mount Havelock — removes chlorine taste and odour.
Waterdrop
TSA Under-Sink Filter (Fluoride + PFAS)
4.4 · 2,237 ratings on Amazon
A reliable tsa under-sink filter (fluoride + pfas) suitable for Mount Havelock's water profile.
Purewell
8.5L Stainless Steel Gravity System
4.4 · 1,137 ratings on Amazon
Ideal for Mount Havelock — removes chlorine taste and odour.
Comparison
How Mount Havelock compares
Compared to South Australia and national averages
| Metric | Mount Havelock | SA Avg | National Avg |
|---|---|---|---|
| Hardness | 89 mg/L | 119.3 mg/L | 85.1 mg/L |
| pH | 0.05 | 3.2 | 8.4 |
| Fluoride | 0.1 mg/L | 0.5 mg/L | 0.7 mg/L |
| Chlorine | 1.1 mg/L | — | — |
| Turbidity | 0.1 NTU | 0.1 NTU | 0.4 NTU |
| TDS | 298 mg/L | 341.5 mg/L | 275.7 mg/L |
Full Results
Detailed water quality data
All values compared against Australian Drinking Water Guidelines (ADWG)
| Parameter | Value | Unit | ADWG Guideline | Status |
|---|---|---|---|---|
| Alkalinity | 76 | mg/L | No limit | Measured |
| Aluminium | 0.006 | mg/L | < 0.2 | Good |
| Calcium | 14.2 | mg/L | No limit | Measured |
| Chloride | 93 | mg/L | < 250 | Good |
| Free Chlorine | 1.1 | mg/L | < 5 | Good |
| Total Chlorine | 1.2 | mg/L | < 5 | Good |
| Colour | 1 | HU | < 15 | Good |
| Copper | 0.003 | mg/L | < 2 | Good |
| E. coli | 0 | cfu/100mL | < 0 | Compliant |
| Fluoride | 0.1 | mg/L | < 1.5 | Good |
| Hardness | 89 | PPM or mg/L | < 200 | Good |
| Iron | 0.0027 | mg/L | < 0.3 | Good |
| Lead | 0.0002 | mg/L | < 0.01 | Good |
| Magnesium | 12.8 | mg/L | No limit | Measured |
| Manganese | 0.001 | mg/L | < 0.1 | Good |
| Nitrate | 0.014 | mg/L | < 50 | Good |
| pH | 0.05 | µg/L | 6.5 – 8.5 | Outside range |
| Sodium | 76.5 | mg/L | < 180 | Good |
| Sulfate | 44 | mg/L | < 500 | Good |
| Total Dissolved Solids | 298 | mg/L | < 600 | Good |
| Turbidity | 0.1 | NTU | < 5 | Good |
Safety
Safety assessment
Of 21 parameters tested, most fall within Australian Drinking Water Guidelines with 1 exception: pH at 0.05 µg/L. E. coli was not detected, meeting the ADWG standard for microbiological safety.
Based on comparison with Australian Drinking Water Guidelines (ADWG)
Explained
What these numbers mean
Moderately hard (89 mg/L)
Water Hardness
Your water is moderately hard. You may notice light limescale deposits on kettle elements and taps over time. Soap lathers reasonably well, though slightly more product may be needed. Skin and hair are generally unaffected, and appliance lifespan should not be significantly reduced at this level.
Outside Range
pH Level
pH of 0.05 is outside the ideal range of 6.5–8.5. The ADWG recommends pH between 6.5 and 8.5 for drinking water.
Low fluoride
Fluoride
Fluoride at 0.1 mg/L. Below the recommended range.
Chlorine
Disinfection
Chlorine measured at 1.1 mg/L, well within the ADWG guideline of 5 mg/L. Used for disinfection to keep water safe. May affect taste slightly — refrigerating water or using a carbon filter can help.
Learn more about these measurements in our water quality glossary — including Hardness , pH , Fluoride , and ADWG guidelines .
Advice
Practical tips for residents
Reduce Chlorine Taste
Mount Havelock's chlorine level is 1.1 mg/L. An activated carbon jug filter or benchtop unit can noticeably reduce chlorine taste and odour from tap water.
Soft Water Advantage
Mount Havelock's water is moderately hard at 89 mg/L. You can use less soap and detergent, as it lathers easily with softer water.
Fluoride in Your Water
Fluoride measures 0.1 mg/L in Mount Havelock. Australian guidelines allow up to 1.5 mg/L. This is added by utilities to support dental health in the community.
Slightly Acidic Water
pH measures 0.05 in Mount Havelock, which is slightly acidic. Running the tap for 30 seconds before drinking can flush any metals that dissolve more readily in acidic water.
Get water quality alerts
We'll email you when Mount Havelock's water data is updated.
FAQ
Frequently asked questions
Is tap water safe to drink in Mount Havelock?
How hard is the water in Mount Havelock?
What water utility supplies Mount Havelock?
Does Mount Havelock water have fluoride?
What is the water quality score for Mount Havelock?
Supplier
Water utility
- Utility
- SA Water
- Supply Zone
- Hawker
- Data Source
- SA Water — water quality performance results november 2025
Nearby
Nearby suburbs
Same water utility, similar water quality
Similar Quality
Suburbs with similar water quality
Suburbs scoring between 8.0 and 10.0
Utility reports average the grid — not your home
Mount Havelock's water meets ADWG standards at the source, but old pipes, roof tanks, and ageing plumbing can add lead, copper or bacteria before the water reaches your tap. These won't show up in your utility report.
Check your own tap before buying a filter or assuming the suburb average matches your home.
Tetra
EasyStrips 6-in-1 Water Test (100 strips)
4.6 · 8,650 ratings on Amazon
Tests 6 parameters in 60 seconds: hardness, chlorine, pH, nitrate, nitrite, alkalinity. Cheapest way to verify your utility data.
Test my tap →Sponsored Amazon link. Check Amazon for current price and availability.
Heavy Metals
Drinking Water Test Kit (Lead, Copper, Iron, Mercury)
4.2 · 250 ratings on Amazon
20 tests. Detects lead, copper, iron, mercury — the things utility reports miss. Mobile-app results, EPA-standard thresholds.
Check metals kit →Sponsored Amazon link. Check Amazon for current price and availability.
Guides for Adelaide and SA
In-depth articles on the water supply that serves Mount Havelock
Related
Explore more
Related pages for Mount Havelock, SA
Is tap water safe?
Safety assessment
Water hardness
89 mg/L
Best water filter
Filter recommendations
South Australia water quality
State coverage
SA Water
Water utility
Compare with Prelinna
Mount Havelock vs Prelinna
Compare with Shaggy Ridge
Mount Havelock vs Shaggy Ridge
Compare with Black Hill Station
Mount Havelock vs Black Hill Station
Disclaimer: The information on this page is for general informational purposes only and does not constitute medical advice, health recommendations, or professional guidance. Water quality data is sourced from SA Water (2025 report) and reflects conditions at the time of utility testing — it may not reflect real-time water quality at your tap. Actual water quality can vary due to local plumbing, seasonal changes, and distance from the treatment plant. For specific health concerns, consult a qualified health professional. For the most current water quality information, contact your local water utility directly. See our Terms of Use.